Mk-diamond MK-6000 Series Manuel d'utilisateur

Kubota DieselCAUTION: Read all safety and operating instructions before using this equipment. This manual MUST accompany the equipment at all times. M

10MK-6000 Concrete Saw Decal Sheet, Part No. 166009Decal CDecal D, E & GDecal FDecal ADecal BDecal HDecal JDecal KDecal IRead entire operatorʼs ma

11SAFETY DECAL LOCATIONSDecal EDecal B, C, DDecal ADecal Location DescriptionA Machine Front Caution Keep Hands and Feet ClearB Top of Belt Gu

12The following is a list of console controls elements:CONSOLE CONTROLSMK-6000 SAW

13CONSOLE CONTROL DESCRIPTIONSMK-6000 SAW CONSOLE CONTROLDecal Name Function

14MK-6000 SAW SPECIFICATIONS59 Hp SerieSMK-6020-KBMK-6026KB MK-6030KB MK-6036KBPart # 165

15MK-6000 SAW SPECIFICATIONS66 Hp SerieS MK-6620-KBG MK-6626-KBG MK-6630-KBG MK-6636-KBGPart

16GENERAL SPECIFICATIONSArbor Size 1" (25.4mm) w/ 3/8" Drive PinBlade Shaft Diameter 2" (58 mm)Blade Shaft Bearings Oil BathBlade Shaft

17MK-6000 SAW SPECIFICATIONSSAW DIMENSIONSItem Description Inches (mm)AHeight 53-1/2"

18MK-6000 SAW PRODUCT SPECIFICATIONSINSTRUCTIONS FOR CHANGING BLADE SPEED FOR SINGLE SPEED SAWSWARNINGDo not exceed blade

19MK-6000 SAW GEAR BOXINSTRUCTIONS FOR CHANGING BLADE SPEED FOR THREE SPEED SAWSDANGER! CAUTION

22INTRODUCTION Congratulations on your purchase of a MK-6000 Concrete Saw. We are certain that you will be pleased with your purchase. MK Diamond t

20Powerband Tension To Tension PowerbandTransmission Belt TensionMK-6000 SAW INSPECTION & START-UPBELT AND POWERBAND

21MK-6000 SAW INSPECTION & START-UPPRE-OPERATION CHECKLISTWARNINGBefore leaving our factory, every machine is thoroughly tested. Follow instructi

223. Pull off vi-lock washers and outer ange. 4. Install new blade.5. Slide the outer ange in place.6. Slide on the vi-lock washers. Ensure the

23MK-6000 SAW OPERATIONWARNINGObserve the rotation arrow on blade and DO NOT exceed maximum RPM stamped on th

24MK-6000 SAW OPERATIONNOTICERead the engine instructions manual before starting.1. Check engine oil. Add oil if low

25MK-6000 SAW OPERATIONWARNINGThis operation is performed with the engine “OFF”!The front and rear pointers are set in

26MK-6000 SAW OPERATIONWARNINGThe blade is spinning whenever the saw is running. Raise the blade as high as possible wh

27This saw is driven by a hydrostatic transmission. To engage the transmission, PULL the Neutral En-gagement Handle up and turn to either direction to

28The saw is equipped with a Depth Indicator and a Depth Stop. The Depth Indicator tells you approximately how deep you are in the cut. To set the ind

29Due to the dusty conditions created by sawing, it is essential to check the engine air cleaner element daily. Remove the element and shake out the a

3SAFETY PAGE NO.Safety Message/Alert Symbols 4Safety Warnings 5Rules for Safe Operation & Transportation 6-8Operation & Safety Decals 1

30MAINTENANCE SCHEDULEMK-6000 SAW MAINTENANCEMAINTENANCE SCHEDULE DAILY25 HOURS50 HOURS250 HOURSCheck Engine Oi

31TROUBLESHOOTINGMK-6000 SAW MAINTENANCETRANSMISSIONCauseProblemLoose Transmission LinkageOil LevelCooling Fa

32NOTES

33NOTES

34MK-6000 SAW ORDERING, RETURN, & PACKAGINGORDERING INFORMATIONRETURN MATERIALS POLICYTo expedite the

35MK-6000 SAW CONTACT & LIMITED WARRANTYCONTACTPlease contact MK Diamond Products, Inc. Custome

MK-6000 SAWOWNER'S MANUAL & OPERATING INSTRUCTIONS MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-5830Pho

4Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Precaution and Operating

5SILICA DUST WARNINGGrinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals

6 •DONOT operate or service this equipment before reading this entire manual. Read and understand all warnings, instr

7• CAUTION must be observed while servicing the machine. Rotating parts can cause injury if contacted. Have all service performed by competent servi

8• Make sure the blade is not contacting anything before starting the engine. • ALWAYS cut in a straight line. DO NOT cut deeper than 1” per pass wi

9NOTES