Mk-diamond MK-660 Manuel d'utilisateur

05.2014MK-660 TILE SAWOWNER'S MANUALPARTS LIST &OPERATING INSTRUCTIONSwww.mkdiamond.comCaution: Read all safety and operating instructions be

10WARNINGWARNINGTo reduce the risk of electrocution, keep all connections dry and off the ground. A Ground Fault Circuit Interrupter (GFCI) should be

11To avoid the possibility of the appliance or plug receptacle getting wet, position the machine to one side of a wall mounted receptacle. This will

12 MK-660 TILE SAW SAFETYEXTENSION CORD LENGTHNameplate Amperes115V 25' 50' 75' 100' 150

13The warning labels contain important safety information. Please read the information contained on each safety label. These labels are considered a p

14PRODUCT SPECIFICATIONSThe MK-660 Saw is a versatile Tile Saw. Operated and used according to this manual, the MK-660 will provide years of dependabl

1504.2010MK-660 SERIESOWNERS MANUALPARTS LIST &OPERATING INSTRUCTIONSwww.mkdiamond.comCaution: Read all safety and operating instructions before u

16TRANSPORTThe MK-660 Saw is designed with a rigid frame and removable Cutting Head. Always use proper lifting techniques when lifting the MK-660 Saw.

17(A) Place the Flat Washer onto the Height Adjusting Knob MK-660 TILE SAW ASSEMBLYCUTTING HEAD INSTALLATIONFo

18 MK-660 TILE SAW ASSEMBLY(D) Locate the Inner Flange Wrench Retaining Holes (E) Install Diamond Blade onto

19 MK-660 TILE SAW ASSEMBLYSPLASH GUARD INSTALLATIONFollow the assembly instructions to prepare your MK-660 Saw for

2INTRODUCTION Congratulations on your purchase of a MK-660 Saw. We are certain that you will be pleased with your purchase. MK Diamond takes pride

201. To prevent the possibility of electrical shock, the MK-660 Saw MUST be de-energized when connecting the Water Pump. 2. To prevent the poss

21 MK-660 TILE SAW ASSEMBLYWATER PUMP SETUP FOR OPERATIONThe Water Pump can be setup for operation in two ways, Ext

221. Check for damaged, broken, or missing parts. 2. Verify the On/Off switch is in the OFF position. 3. Before connecting the MK-660 Saw to a

23DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. MK-660 TILE SAW

24 MK-660 TILE SAW OPERATIONDIAGONAL CUTTINGNOTE:To cut 45º Diagonals, the 45º Flat Angle Guide (MK Diamond Part No

25 MK-660 TILE SAW OPERATION45° MITER CUTTINGNOTE:To cut 45º Miters, the 45º Bullnose Miter Guide (MK Diamond Part N

26 MK-660 TILE SAW OPERATIONOFF-ANGLE CUTTINGNOTE:DO NOT FORCE THE TOOL. It will do the job better and safer at th

27 MK-660 TILE SAW CLEANUP(J) Turn the motor OFF when work is completeCLEANUPNOTE: 1. If an external water sou

28 MK-660 TILE SAW CLEANUP(G) Clean the MK-660 Saw with soap and clean water(H) Remove the Water Pan from the

29 MK-660 TILE SAW MAINTENANCE(D) Lubricate the Roller Wheel AssemblyMONTHLY MAINTENANCEThe following maintenance should

3TABLE OF CONTENTS SAFETYRules for Safe Operation 4-7California Proposition 65 Message 8Electrical Requirements 9-12Safety Label Locations 13 Pro

30 MK-660 TILE SAW MAINTENANCE(G) Locate the Motor Shaft Align-ment Pin(H) Align the Alignment Slot of the Inner Flange

31 MK-660 TILE SAW MAINTENANCE(P) Verify the Cutting Table Roller Wheel Assembly is tightFLOW ADJUSTMENTIf ow to the Di

32 MK-660 TILE SAW MAINTENANCEBLADE DRESSINGLike most cutting instruments, a Diamond Blade performs best when it is dress

33 MK-660 TILE SAW MAINTENANCEDIAMOND BLADE CHANGE-OUTWhen installing the Retaining Screw, do not "cross-thread"

34 MK-660 TILE SAW TROUBLESHOOTINGBLADE WILL NOT CUT PROPERLY(B)Check for proper rotation(A)Check for Smoothness or “Glazing" (Dres

35COOLING FLOW(B)Remove the Transfer Tube from the Blade Guard inlet, go to Step C(A)Check Flow Adjusting Clamp is open. If flow exists, go to Step B(

36BLADE STOPS TURNING(A)Allow motor to cool and depress motor Overload Reset Switch(C)Check Ground Fault Circuit Interrupter (GFCI) is not tripped(B)V

37NOTES

38 MK-660 TILE SAW EXPLODED VIEW

39 MK-660 TILE SAW PARTS LISTITEM DESCRIPTION QTY PART # A Accessories 1 n/a A1 Carton, Accessory Pack, 660 1

4 MK-660 TILE SAW SAFETYRead and follow all safety, operating and maintenance instructions. Failure to re

40ITEM DESCRIPTION QTY PART # D21 Boot, Thermal Overload Switch 1 167983 D22 Switch, 15A\125V Lighted Rocker 1 153421 D23 Rectier, 40 Amp

41ITEM NUMBER DESCRIPTION1. 158434 MK-225, 7 x 5/8 Arbor2. 139311 MK-215, 7 x 5/8 Arbor3. 153293 MK-315, 7 x 5/8 Arbor4. 134577-MK Dual 45° Flat Angle

42 MK-660 TILE SAW ORDERING & RETURN INSTRUCTIONORDERING INFORMATIONYou may order MK Diamond products through your local MK Diamond distri

43 MK-660 TILE SAW CONTACT & WARRANTYCONTACTPlease contact MK Diamond Products, Inc. Customer Service Department

MK-660 TILE SAWOWNER'S MANUAL, PARTS LIST & OPERATING INSTRUCTIONS MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (

5 MK-660 TILE SAW SAFETYON(())ON(())ON(())All visitors and children should be kept a safe distance from w

6 MK-660 TILE SAW SAFETYConsult the owner’s manual for recommended accessories. Using improper accesso

7 MK-660 TILE SAW SAFETYBefore using a power tool, check for damaged parts. A guard or any other part t

8 MK-660 TILE SAW SAFETYSawing, grinding and drilling generate dust. Excessive airborne particles may cause

9 MK-660 TILE SAW SAFETYWARNINGIn order to prevent electrical shock and injury, the following electrical sa